SOCOM Gear #7 11.1V 1000 mAh 15C Stick Lipoly Airsoft Battery
Enhance your AEG BPS(balls per second, bb's per second) with this 11.1V 1000 mAh 15C Stick Lipoly Airsoft Battery by SOCOM GEAR. This battery will give you a higher voltage, and a higher current... Last, but not least you get all of this with a special LESS hazardous formula.
- HIGH PERFORMANCE AND LESS HAZARDOUS FORMULA
- SPECIAL DESIGN FOR AIRSOFT AEGS; NOT AN RC REBRAND BATTERY
- CE [BCT07CC-116E] AND SGS CERTIFIED [EC405564100]
NOTE: The CE marking (an acronym for the French "Conformite Europeenne") certifies that a product has met EU health, safety, and environmental requirements, which ensure consumer safety.
Nominal Capacity 1500mAh* / Nominal Voltage 11.1V / CELL internal resistance C20mC / Charge Current max.1.5A(1C)
Voltage max.4.25V / Discharge Continuous Current Max.22.5A per cell, 67.5A per pack(15C) / Burst Current Max.30.0A per cell 90A per pack (20C) / Voltage cut-off 3.0V/ Cycle Life / 80% Retention / 1C 500 cycle / 10 C 100 cycle / Self -Discharge <8% per month / Operating Temperature Range /Charge 0 degrees C around 45 degrees C 32 degrees F around 113 degrees F / Discharge -20 degrees C 60 degrees F -4 degrees F around 140 degrees F / Storage -20 degrees C around 40 degrees C -4 degrees F around 104 degrees F / Pack Dimension Thickness 16.0+/-0.5mm 0.63+/-0.05 in. / Width 34.0+/-0.5mm 1.34+/-0.05 in. / Length 102.0+/-1.0mm 4.16+/-0.05 in. / Weight Appro 114.0g
Nominal capacity (average discharge capacity) : discharge current 0.5C, end of voltage 3.0V, temperature 23+/-2C.
Nominal voltage (average discharge voltage): discharge current 0.5C, end of voltage 3.0 V, temperature 23+/-2C.
Failure to follow these instructions can quickly result in leak, explosion, or permanent damage to the batteries and its surrounding and may even start a fire.
- (1) A new battery comes in a discharged condition and must be charged before use (refer to the device manual for charging instructions).
- (2) The battery should be used in the environment as listed below. Otherwise, the battery lifespan and function would be substantially reduced. Under extreme environments, batteries may overheat, explode, or even catch fire
- (3) Similar to NiCd and NiMH batteries, lithium-polymer batteries can release extremely high voltages.
- (4) Always use battery manufacture approved chargers to recharge the batteries.
- (5) Always empty the chamber of your AEG, remove the magazine, put on barrel cap and put on safety before you change the battery.
- (6) Never place the battery near the heater, fire, or any heat sources. Never throw the battery into the water or keep the batteries in a damp environment.
- (7) Never allow a battery's positive and negative leads to accidentally touch each other.
- (8) Never connect the battery to the wall plug or cigarette lighter plug in vehicles.
- (9) Never dispose batteries with fire or warm up the battery using any heat sources.
- (10) To avoid short-circuit, all batteries should be stored or shipped free of any conductive materials, including necklace, hairpin or any metals.
- (11) Never hit or throw the battery against any walls, floors or hard subjects which may damage the batteries by violent mechanical vibration.
- (12) Never use hammer, nail or any sharp object to pierce or penetrate through the battery insulator.
- (13) Never solder the battery's connectors with wires.
- (14) Never disassemble the batteries in any means.
- (15) Never charge the battery in an extreme hot environment.
- (16) Never place the battery in a microwave or pressurized container.
- (17) Never use the lithium-polymer batteries with the disposable batteries or rechargeable batteries in different types, capacity or brands.
- (18) Before and after every use of your lithium-polymer batteries, inspect all cells in the pack as much as possible to ensure no physical damages, discolor, heat emission, or swelling in evident. Such signs can often indicate that a dangerous problem exists and the batteries should be disconnected and disposed immediately.
- (19) Always store the lithium-polymer batteries in a secure location. Lipo batteries are to be handled by adults only
- (20) Remove or dispose the batteries immediately when batteries are leaking watery substance and emit strange order.
- (21) Do not allow the battery's electrolyte to get in the eyes or skin. Wash affected areas with soap and water immediately if they come in contact with the electrolyte. If electrolyte makes contact with the eyes, flush with large amounts of water for 15 minutes and seek medical attention immediately.
- (22) To prolong battery life-span and to ensure battery full function, charged battery should rest for at least one hour before discharging.
- (23) Never keep the batteries in an extreme environment, such as direct under sun light or inside the car during hot summer. Otherwise, batteries will overheat or even ignited to substantially shorten the lifespan and damage the function of the batteries.
- Working environment: Charge:0C~45C/ Discharge: -20C~60C / Storage for 30 days:-20C~45C / Storage for 90 days:-20C~35C =
Zephyr Sports Airsoft Battery Disclaimer:
Zephyr Sports is not responsible for batteries that have been damaged as a result of improper operation, storage, misuse or abuse, accident or neglect, such as physical damage resulting from misuse; contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like, extreme heat, or food; use of the battery for commercial purposes or subjecting the battery to abnormal usage conditions, or other acts which are not the fault of Zephyr Sports. Make sure you understand how your battery should be used and how long it should be charged. We recommend that you always use a smart charger to avoid damaging your airsoft batteries. If you have any doubt regarding the operation, charging, or storage of your battery and/or charger, please contact us. A charging battery should not be left unattended and should be picked up periodically while charging to check for overheating. Do not charge batteries near flammable material.
More knowledge of Li-Po Batteries:
(1) What are factors to enhance the shooting speed (BPS, B.B. per Second)C Voltage, Currents and C. =All three!=
(2) What is your battery's continuous currentC =mAh x C=mA, For example, Our 1500mAh, 10C battery, the continuous current will be 1500mAh x 10C =15000mA=15A (pre cell) A 11.1 Volt Li-Po batteries have 3 cells, so, the continuous currents will be 15Ax3 (cells)=45A=
(3) What's the current (A) my AEG needsC =An extreme example: 120 meter/sec (393ft/sec) + 40 BPS (B.B. per Second) need about 60A. Normal AEG without modification (300 ft/sec) + 10 BPS only need start current at 20A.=
(4) What is my battery lifeC =Depends on the current your AEG needs. The lower current of your AEG, the longer battery life.=
(5) How come people say the Li-Po batteries are dangerousC =Normally, if you use the right charger, don't pinch or penetrate your battery, the battery is very safe. However, no one can guarantee the 100% safety of the Li-Po battery, If you find your the battery expending, leaking, or become extremely hot, please disconnect the battery immediately. Please read the WARNING section on the main product page for more details. If you need the 100% safe Li-ion battery, please contact MadBull Airsoft. Their LFP batteries are the only 100% safe batteries in the industry.=
(6) How to tell other brands Li-Po batteries is stating the correct C value informationC =For example, there is a battery company states that their battery is 11.1V, 2100mAh, 20C, 42A. Is this the correct informationC First, let's check the C value is correct or not. Let's do the calculation: 42A for 3 cells means each cell comes with 14A. As you know that mAh x C = mA, 2100mAh X C = 14A =14000mA., So, the C=6. You have to doubt their C value.=
(7) Should I choose the T style (T-plug) connector (red color) or should I use the original JST connector (white color)C =The standard JST connector can take 80A. Unless your AEG take a lot of current (A,) you don't have to change to T style connector. However, a lot of AEG company's JST connector didn't meet the standard (using low quality materials), in this case, you'd better change your connector.=
(8) What is shortage happenedC =For example, your connector melt or your fuses touch to other metals. If the positive and negative wires contact each other, your wiring cable will become extremely hot and will burn down the connector on the battery. Once the wiring get off the connector, it stops melting and burning. Unless you have expert to help you rebuild your battery, we will suggest you to recycle your battery.=
(9) Let's see what happened if I penetrate my battery or if I use the wrong charger to charge my batteryC =There are video uploaded at www.SOCOMGEAR.com If you penetrate your SOCOM Li-Po battery, the battery will generate a lot of black smoke and the battery will become hot. When SOCOM GEAR did the testing, they used a thick cardboard under the battery and didn't cause fire. However, this didn't guarantee that you won't get fire under the similar conditions. SOCOM GEAR's battery formula will reduce flame and heat but didn't guarantee that it won't catch fire. So, never try to penetrate your battery. If you use the wrong charger, per the testing video, the battery will only expand and stop working. However, don't use the wrong charger. SOCOM GEAR can't guarantee that it won't catch fire or explosion under the similar condition.=